JEE ADVANCED Previous Year Papers 2018: Candidates who are going to appear in JEE Advance Examination on 20-05-2018 they must download JEE ADVANCED Previous Year Papers for better preparation.
Interested candidates have to apply from 02-05-2018 to 07-05-2018. Through PAST Years JEE ADVANCED Question Papers candidates will be able to practice for the national level engineering exam.
Joint Entrance Examination (JEE) Advanced 2018- Check Details

 Conducting Body Indian Institute of Technology Exam Name JEE Advanced 2018 JEE Advance Date Of Exam 20-05-2018 Category JEE ADVANCED Previous Year Papers 2018

The JEE ADVANCED Previous Year Papersare similar to the original questions papers and will help the candidates know what type of questions are usually asked in the examination. JEE advanced paper is held in English as well as in Hindi language.

The JEE Advanced Admit Card for the 20th May examination will be released on 14th May. All candidates know very well that practice with solving the JEE advanced previous year solved paper is the best way of preparation.

Candidates are advised to download JEE advanced previous year papers and solve them like a real exam. You can also go through below stated important questions of JEE Advanced 2018:

Question-1) The first mechanical calculating machine was made by:
1.       William Oughtred
2.       Gottfried Leibnitz
3.       Blaise Pascal
4.       Charles Babbage
5.       None of the above

Check Here What’s New In: JEE Advanced Syllabus

Question-2) Multiplication of 1112 by 1012 is
1.       1100112
2.       1000112
3.       1111002
4.       0001012
5.       None of the above

Question-3) A Winchester disk is a
1.       Disk Stack
2.       Removable disk
3.       Flexible disk
4.       All of the above
5.       None of the above

Question-4) A prewritten program that’s sold to perform a common task is called an application
1.       System software
2.       Package
3.       Utilities
4.       Program
5.       None of the above

Question-5) If an analog signal is to be converted to an 8-bit resolution, how many comparators are used in a parallel-encoded ADC?
1.       127
2.       128
3.       255
4.       256

Question-6) Referring to the given figure, what appears to be wrong, if anything, with the output of the D/A converter?
1.       The input signal is probably noisy.
2.       There appears to be some nonlinearity in the scope display.
3.       The converter has a nonmonotonic output error.
4.       It appears that certain input codes are incorrect; double-check the input coding.

Question-7) A certain digital-to-analog converter has a step size of 0.25 V and a full-scale output of 7.75 V. Determine the percent of resolution and the number of input binary bits.
1.       31%, 4 bits
2.       3.23%, 4 bits
3.       31%, 5 bits
4.       3.23%, 5 bits

Question-8) What is the major advantage of the R/2R ladder DAC as compared to a binary-weighted-input DAC?
1.       It has fewer parts for the same number of inputs.
2.       It is much easier to analyze its operation.
3.       It uses only two different resistor values.
4.       The virtual ground is eliminated and the circuit is therefore easier to understand and troubleshoot.

Question-9) From the truth table below, determine the standard SOP expression.

Question-10) Derive the Boolean expression for the logic circuit shown below:

Question-11) Which of the following expressions is in the sum-of-products (SOP) form?
1.       (A + B)(C + D)
2.       (A)B(CD)
3.       AB(CD)
4.       AB + CD

Question-12) Which of the following combinations cannot be combined into K-map groups?
1.       corners in the same row
2.       corners in the same column
3.       diagonal
4.       overlapping combinations

Question-13) The problem of the VOH(min) of a TTL IC being too low to drive a CMOS circuit and meet the CMOS requirement of VIH(min) is usually easily overcome by:
1.       adding an external pull-up resistor to VCC
2.       adding a fixed voltage-divider bias resistive network at the output of the TTL device
3.       avoiding this condition and only using TTL to drive TTL
4.       adding an external pull-down resistor to ground

Question-14) The rise time (tr) is the time it takes for a pulse to rise from its ________ point up to its ________ point. The fall time (tf) is the length of time it takes to fall from the ________ to the ________ point.
1.       10%, 90%, 90%, 10%
2.       90%, 10%, 10%, 90%
3.       20%, 80%, 80%, 20%
4.       10%, 70.7%, 70.7%, 10%

Question-15) The compressive strength of cement should not be less than about 110Kg/cm2 after three days & not less than 170Kg/cm2 after seven days. The fineness of an ordinary cement as determined by turbid metric method should be about __________ cm2/gm.
1.       800
2.       1600
3.       4000
4.       8500

Question-16) what should be done with unused inputs to a TTL NAND gate?
1.       let them float
2.       tie them LOW
3.       tie them HIGH

Question-17) the normal stress is the same in all directions at a point in a fluid, when the fluid is
1.       Non-viscous
2.       Incompressible
3.       both (a) and (b)
4.       having no motion of one fluid layer relative to the other.

Question-18) Brownian movement is prominent in the particle size range of __________ microns in case of settling of a particle in a fluid.
1.       2 to 3
2.       to 0.10
3.       200 to 300
4.       100 to 1000

Question-19) Shear stress in a fluid flowing in a round pipe
1.    Varies parabolically across the cross-section.
2.    remains constant over the cross-section.
3.    is zero at the centre and varies linearly with the radius.
4.    is zero at the wall and increases linearly to the centre.

Question-20) For the same terminal conditions and fitting size, the least friction loss is incurred in a/an
1.    T-joint
2.    union
3.    45° elbow
4.    90°bend